Short answer: Stone grain edge banding is a roll printed and textured to look like concrete, marble or natural stone, made for panels whose face carries the same pattern. To match one, read the decor code on the board (for example UNIBOARD V05, PRISM SF239 Storm or ALVIC Porcelain 3), pick the roll matched to that code, and check a sample against an offcut before you buy full rolls. A plain gray edge on a speckled or veined face shows at every corner.
This guide is for cabinet shops, fixture builders and designers working with stone-look and concrete-look laminate, TFL and gloss panels. Our stone-look rolls are spread across the solid color, wood grain and high gloss collections, so the table below puts them in one place.
Key takeaways
- Stone-look edges belong on faces with speckle, mottling, cloudiness or veining. Plain grays need a solid color edge instead.
- The decor code decides the match. "Gray concrete" describes dozens of boards that are not interchangeable.
- Match three things: base color, pattern type (speckle, cloud, concrete or vein) and sheen.
- Some decors have "stone" in the name but are not stone patterns, such as EGGER U727 Stone Grey, which is a solid color.
- Every roll in the table below is listed in 1 mm x 15/16 in x 300 ft. Check a free sample before a full order.
What is stone grain edge banding?
It is edge banding whose surface copies a mineral look: fine speckle like terrazzo or granite, soft clouds like limestone, mottled concrete, or white veining like marble. It finishes the cut edge of a panel with the same face, so a vanity, reception desk or bar front reads as one solid piece. Shops search for it as stone grain, stone texture or stone-look edge banding; they all mean the same thing.
The difference from a solid color roll is the pattern. A solid color edge is one even tone. A stone-look edge has variation in it, and that variation is what hides the joint line on a patterned face.
Which stone-look rolls can you start with?
These are the stone, concrete and marble looks we match today, grouped by look. Decor names are written the way they appear on our product pages, and each brand name only tells you which panel the roll is matched to.
| Look | Matched to | What the product page describes | Roll |
|---|---|---|---|
| Light stone and cloudy looks | |||
| Pale speckled stone | EGGER UC01 | Pale gray-white with a fine speckled, stone-like texture | EGGER UC01 (CT10078M) |
| Light cloudy stone | UNIBOARD HPL K40 Light Grey Cloudy Stone-Look | Light gray with a soft cloudy texture | UNIBOARD K40 (CT90042M) |
| Light stone, high gloss | ALVIC Porcelain 2 (Porcelain Stone-Look High Gloss) | Stone-look decor with a high gloss finish; judge the tone on a sample | ALVIC Porcelain 2 (CT50024M) |
| Concrete and mid-gray textures | |||
| Mottled concrete | UNIBOARD HPL V05 Grey Concrete-Look | Gray with a mottled concrete look | UNIBOARD V05 (CT90136M) |
| Grooved concrete | ARAUCO PRISM WF393 Concrete Groovz | Light gray with a grooved concrete-wood texture | PRISM WF393 (CT80039M) |
| Fine speckle, mid gray | UNIBOARD HPL K29 Medium Grey Textured | Even medium gray with a fine speckled texture | UNIBOARD K29 (CT90069M) |
| Dark stone and marble | |||
| Blue-gray mottled stone | EGGER UC02 | Darker blue-gray with a soft, mottled stone-like texture | EGGER UC02 (CT10079M) |
| Dark gray stone | ARAUCO PRISM SF239 Storm | Dark storm gray with a fine stone texture | PRISM SF239 Storm (CT80024M) |
| Charcoal stone | ARAUCO PRISM SF237 Charcoal | Charcoal black with a fine stone texture | PRISM SF237 Charcoal (CT80023M) |
| Textured gray-brown stone | ALVIC Muratti 4 (Muratti Dark Grey Stone) | Gray-brown with a textured stone finish | ALVIC Muratti 4 (CT50050M) |
| Black marble, high gloss | ALVIC Porcelain 3 (Porcelain Black Marble High Gloss) | Black marble with white veining and a high gloss finish | ALVIC Porcelain 3 (CT50025M) |
All 11 rolls above are listed in one size: 1 mm thick, 15/16 in (23 mm) wide, 300 ft long. If your decor is not in the table, browse the solid color edge banding collection, the wood grain collection and the high gloss collection, since stone looks are filed under all three.
How do you match edge banding to a stone-look panel?
- Find the full decor code. Look on the panel label, the cut list or the supplier quote. A code like SF239 or K40 narrows the match to one roll; a color name alone does not.
- Name the pattern type. Is the face speckled, cloudy, mottled like concrete, grooved, or veined like marble? A speckled edge next to a veined face looks wrong even when the base color is close.
- Check the sheen. ALVIC Porcelain 2 and Porcelain 3 are high gloss. A gloss edge on a matte stone face, or the other way around, shows as a stripe of different light.
- Order a sample of the roll matched to that code. Use the sample page and request the exact roll from the table.
- Compare in the room's light. Hold the sample against an offcut at the panel edge, under the lighting where the piece will stand. Stone patterns can lean warm or cool under different bulbs.
- Work out the footage and order. Total the edges you will band, add a margin for trimming, and divide by 300 ft per roll. The edge banding calculator guide walks through it.
Why does a stone-look edge never match the face exactly?
A 15/16 in strip is too narrow to carry the full pattern of a 4 x 8 sheet. The edge reproduces the base color, the size of the speckle or cloud, and the surface texture, but a marble vein or a large concrete patch will not line up with the same feature on the face. That is normal for any stone-look edge. What you are judging is whether the edge reads as the same material from a normal viewing distance, not whether each vein continues around the corner.
This is also why an edge that looks right on a small chip can look off on a long countertop gable. When a job has long exposed edges, compare the sample along the longest edge you will band, not just at a corner.
Which "stone" names are not stone patterns?
Several decors use stone words in the name but have a different surface. Ordering by name alone is the most common way to end up with the wrong roll.
| Decor | What it actually is | Roll |
|---|---|---|
| EGGER U727 ST9 Stone Grey | A solid color with no stone pattern | EGGER U727 ST9 (CT10018M) |
| EGGER H1288 ST19 Stone Grey Frozen Wood | A greige woodgrain | EGGER H1288 ST19 (CT10039M) |
| EGGER H3198 ST19 Stone Grey Frozen Wood | A gray woodgrain | EGGER H3198 ST19 (CT10037M) |
| ALVIC Basalto High Gloss | Listed as a mid stone gray in high gloss, under our high gloss range | ALVIC Basalto (CT50007M) |
The EGGER letter tells you a lot: U codes are solid colors, H codes are woodgrains. Our EGGER matching guide lists every EGGER code we match.
How do you choose between two close stone-look rolls?
- Code on the board matches a roll: order that roll. Do not swap in a "close" gray from another brand.
- No code, but you know the brand: start with that brand's rolls in the table, then check the brand guide for UNIBOARD, ARAUCO PRISM or ALVIC.
- Two rolls look close on screen: order samples of both. Speckle size and undertone are hard to judge from a photo.
- Gloss stone face: stay with a gloss roll and read the high gloss edge banding guide for trimming and buffing care.
- Face is woven or fabric-like rather than mineral: you probably want a textile edge; see the textile edge banding guide.
What mistakes should you avoid with stone-look edges?
- Putting a smooth solid gray on a speckled face. It reads as a painted edge.
- Choosing by the word "stone" in a decor name. Check the table above first.
- Mixing gloss and matte. Porcelain 2 and Porcelain 3 are gloss; the other rolls in the main table are not listed as gloss.
- Judging color on a phone screen. Grays and stone tones shift more on screens than most colors.
- Cutting a full job from a new panel lot without a fresh sample check. Panel colors can drift a little between lots.
Frequently asked questions
Is stone grain edge banding the same as stone texture edge banding?
Yes. Stone grain, stone texture and stone-look are different names for edge banding printed and textured to look like stone, concrete or marble.
Do you have a stone-look collection?
Not as a separate collection. Our stone-look rolls sit in the solid color, wood grain and high gloss collections, which is why this guide lists them together.
What size are your stone-look rolls?
The 11 rolls in the main table are listed in 1 mm x 15/16 in x 300 ft. Check the Size option on each product page before you order.
Is 15/16 in wide enough for 3/4 in panels?
Yes. 15/16 in (about 23 mm) covers a 3/4 in (19 mm) edge with some overhang left for trimming flush.
Which roll matches a white marble with gray veins?
We do not list a white marble roll today. The only marble look in the table is ALVIC Porcelain 3, a black marble with white veining. Email us the code of your white marble panel and we can tell you what we have.
Which roll suits a concrete-look panel?
Start with UNIBOARD V05 Grey Concrete-Look for a mottled concrete face, or ARAUCO PRISM WF393 Concrete Groovz for a grooved concrete-wood face. Match by the code on your board.
Is EGGER U727 Stone Grey a stone pattern?
No. U727 ST9 Stone Grey is a solid color, so its matching roll has a smooth, even surface. It is also listed in a 72 mm width for thick tops.
Is ALVIC Porcelain 2 gray or beige?
Its product page notes that the photos may not show the shade accurately. Judge it from a physical sample next to your ALVIC panel.
Can I use a gloss stone edge on a matte stone panel?
It will usually read as a mismatch, because the edge reflects light differently from the face. Pair gloss with gloss and matte with matte.
Will the veins on the edge line up with the veins on the door?
No. A narrow strip cannot follow the pattern of a full sheet. The edge matches the color, texture and pattern scale, not each individual vein.
My stone-look decor is not in the table. What now?
Search the collections linked above, or send the brand and full decor code to Order@ctedgeband.com.
Can I order one roll?
Yes. One roll is the minimum, and shipping is calculated at checkout. We ship from Chicago.
Who is CT Edge Band?
CT Edge Band Supply, Inc makes matched edge banding in our own factory and ships rolls from our warehouse at 1400 W 37th Street, Chicago, IL 60609. You can order a single roll, and shipping is calculated at checkout. Brand names on our listings (EGGER, UNIBOARD, ARAUCO PRISM, ALVIC and others) only tell you which panel a roll is matched to; the rolls are our own product.
Questions about a stone-look match? Call +1 312-612-0281 or +1 312-612-0284, or email Order@ctedgeband.com. We answer Monday to Saturday, 9am to 8pm EST.
Next step: order a sample of the stone-look roll matched to your panel and hold it against an offcut before you buy rolls. Free samples; shipping is calculated at checkout.
