Short answer: to match edge banding to ALVIC panels, find the decor name on the board label, then match the finish before the color: a high gloss Luxe door needs a high gloss edge, and a super matte Zenit door needs a matte edge. For a 3/4" panel, a 15/16" wide band leaves a little to trim. Check a free sample against your actual board before you order rolls.
Key takeaways
- ALVIC panels come in very different finishes, so the sheen of the edge matters as much as the color.
- High gloss doors show a dull edge right away, and super matte doors show a shiny one.
- Pearl and sparkle decors need an edge with the same effect, not a plain solid color.
- We carry 53 edge banding matches for ALVIC decors, from gloss white to super matte black and wood grains.
- Always compare a sample with the board in the light where it will be installed.
What makes ALVIC panels hard to match?
ALVIC is a Spanish maker of decorative panels and furniture components. Its best-known surfaces are Luxe, a high gloss lacquered surface with a mirror effect, and Zenit, a super matt lacquered surface with a silk touch. It also makes Syncron, a textured surface where the design and the finish line up.
Those finishes sit at opposite ends of the sheen scale. A mirror gloss door makes a semi-gloss edge look cloudy, and a velvety matte door makes a glossy edge look like a stripe of plastic. That is why the finish comes first when you pick an ALVIC match.
Which ALVIC decors do we match, grouped by finish?
Start with the finish group, then narrow down by color. It is the quickest way to get to two or three samples worth ordering.
| Finish group | ALVIC decors we match | What to compare first |
|---|---|---|
| High gloss solids | Blanco Luxe, Blanco Polar, Gris Nube, Gris Perla, Cashmere, Basalto, Antracita, Gris Plomo, Negro | Whether the panel leans warm or cool, and how deep the shine is |
| High gloss colors | Cotto, Agua Marina, Azul Marino | The exact hue in daylight, since strong colors show any shift |
| Pearl and sparkle (PE) | Blanco Colonial PE, Blanco Colonial Pearl, Antracita PE, Gris Plomo PE, Black PE | Whether the edge carries the same fleck or pearl effect as the face |
| Gloss patterns and metallics | Olivo, Guayana, Euroline 03, Metallo 1, Metallo 4, Cuzco Oro, Gris Metallic, Textil Plata, Porcelain 2, Porcelain 3 | Pattern scale and how the metallic or stone figure catches light |
| Super matte (SM) | Blanco Polar SM, Blanco SM, Cashmere SM, Basalto SM, Black SM, Azul Indigo SM | Low sheen first, then color, because any shine shows on a matte door |
| Wood grains | Nocce 1, Nocce 2, Nocce 3, Olmo 2, Olmo 3, Ida 1, Ida 2, Ida 3, Ida 4, Anniversary Oak 2, Anniversary Oak 3, Como Ash 01, Ice Cream 1, Cashmere Natural Wood | Undertone and how strong the grain lines are |
A few more decors, such as Muratti, Picasso and New Agave, are listed on our ALVIC edge banding collection, where you can see every match in one place.
How do you match edge banding to ALVIC panels step by step?
- Find the decor name. Check the panel label, order or spec sheet for the ALVIC decor name and finish, such as Blanco Polar or Cashmere SM.
- Pick the finish group. Gloss, pearl, super matte or wood grain. Use the table above to narrow it down.
- Open the matching product. Each match is listed by the ALVIC decor name, so you can order by name.
- Measure the panel thickness. A 3/4" panel takes a 15/16" (about 23 mm) band, which leaves a small overhang to trim flush.
- Order a free sample. Request it from our free sample page.
- Compare in real light. Hold the sample against the door face near a window and under the room lights, and look at it from an angle to check the sheen.
How do you choose between two close ALVIC matches?
Several ALVIC decors are close, such as Blanco Luxe and Blanco Polar, or Antracita and Antracita PE. When two samples both look right, use these checks:
- Sheen: tilt the panel toward a light. The edge should shine about as much as the face, no more and no less.
- Effect: on a PE or metallic decor, look for the same sparkle or pearl in the edge. A plain edge looks flat next to it.
- Undertone: whites and greys can lean warm or cool. Lay both samples on the board and see which one shares its cast.
- Grain contrast: on wood grains, a board with strong lines needs a band with visible grain, while a calm board looks best with a quieter band.
- Where the edge shows: doors and drawer fronts get the closest look, so test samples against those parts first.
For more on gloss and matte edges, see our guides on making high gloss cabinets look seamless and matching matte, gloss and soft-touch panels.
Frequently asked questions
Is this edge banding made by ALVIC?
No. CT Edge Band makes the edge banding and matches it to ALVIC decors. Luxe, Zenit and Syncron are ALVIC products.
What width do I need for a 3/4" ALVIC panel?
Order 15/16" (about 23 mm). It is a little wider than the panel, so you can trim it flush after it is applied.
Which edge banding goes with ALVIC Zenit super matte doors?
Pick the SM match for your decor, such as Blanco SM or Black SM. A gloss edge will stand out on a super matte door.
Why does the product photo look different from my board?
Screens and photos change gloss, pearl and metallic colors a lot. Judge the match from a physical sample next to the board, not from the photo.
Ready to match your ALVIC project?
Browse the ALVIC matches, order a free sample, or contact our team with your decor name and we will point you to the closest match.
